Milan Technology MIL-SM8002TG Bedienungsanleitung

Rev.A1 18-SEPT-2006 MIL-SM8002TG 9 Port 10/100/1000BASE-T Two Com

2  Broadcast storm filter  DHCP Client, Relay, Server  Per port

92 assigned.  TOS only: the port priority will only follow

93  Save the configuration. Default Port Priority Setting interface COS Configu

94 COS Configuration interface TOS Configuration Set up the TOS pri

95 TOS Configuration interface SNTP Configuration You can configure the SNTP (Sim

96 Local Time Zone Conversion from UTC Time at 12:00 UTCNovember T

97 2ZP4 - USSR Zone 3 +4 hours 4 pmZP5 - USSR Zone 4 +5 hours 5 pmZP6 - USSR Zone 5 +

98 SNTP Configuration interface IGMP Configuration The Internet

99 Report A message sent by a host to the querier to indicate that the host wants to

100 IGMP Configuration interface IGMP Status When you enable the I

101 In the Super ring topology, every switch should enable super ring function and as

3 Port Trunk Support IEEE802.3ad with LACP function. Up to 3 trunk groups and maximum

102 Super ring Interface [NOTE] When you enable the super ring func

103 Security Configuration In this section, you can configure 802.1x, IP, and port s

104 802.1x Configuration interface System Configuration After ena

105 6. NAS, Identifier: set the identifier for the radius client. 7. Save the confi

106 802.1x Per Port Setting interface Misc Configuration 1. Qui

107 re-authenticated. 7. Select <Save> 802.1x Misc Configuration interface

108 MAC Address Configuration interface Static MAC Address You ca

109 4. Select <Add> to save all configure value. 5. Existed Entry: you will s

110  Add the Filtering MAC Address 1. MAC Address: Enter the MAC a

111 All MAC Address interface 2. The selected port of static MAC address informati

4 broadcast packet. Egress rate shaping supports all of packet. Rate

112 Load Factory Default Setting interface Save All Configuration

113 Save All Configuration interface Reboot System Reboot the switch in software r

114 Reboot System interface

115 Web-Based Management Web-Based management offers advanced management featu

116 2. Type http:// and the IP address of the switch. Press “Enter”.

117 bytes.  System Location: assign the switch physical location. The maxim

118  Gateway: assign the switch gateway. The default value is 192.16

119 because the software keeps track of IP addresses rather than requiring an adminis

120 DHCP Server Configuration interface DHCP Client Entries When

121 device. Port and IP Bindings interface Update Firmware It provides the funct

5 Configuration upload and download Support binary format configuration file for syst

122 Update Firmware interface Restore Configuration You can restor

123 1. TFTP Server IP Address: fill in the TFTP server IP 2. Backup File Name: fill

124 Event Configuration You can select the system log events and SMT

125 Event Configuration interface  Port event selection: select the per port even

126  Link UP & Link Down: the system will produce a l

127 SMTP Configuration interface Security Manager You can change web management l

128 Port Statistics The following information provides a view of th

129 Port control interface View the Single Port Information You can direct click

130 Port Trunk The Link Aggregation Control Protocol (LACP) p

131 6. If LACP enable, you can configure LACP Active/Passive status in each ports on

6 Hardware Description Physical Dimension The physical dimensions of

132 Port Trunk – Aggregator Information interface State Activity

133 Trunking – State Activity interface Port Mirroring The Port mirroring is

134 Prot Mirroring interface Rate Limiting You can set up every p

135 Rate Limiting interface  All the ports support port ingress and egress rate c

136 same VLAN members. Basically, creating a VLAN from a switch is lo

137 VLAN – PortBase interface 1. Click Add to create a new VLAN group. 2. Enter

138 VLAN—PortBase Add interface 4. You will see the VLAN displays.

139 that indicates the VLAN numbers. You can create Tag-based VLAN, and enable or d

140 802.1Q Configuration 1. Enable GVRP Protocol: check the check b

141 Group Configuration interface 3. You can Change the VLAN group name and VLAN I

7 LED Indicators The following table provides descriptions of the LED statuses and

142 Group Configuration interface Rapid Spanning Tree The Rapid S

143 the value, you must reboot the switch assign path priority number. The

144 RSTP System Configuration interface RSTP Per Port Configuration

145 4. Edge: The port directly connected to end stations cannot create bridging loop

146 Enter the system name, contact, and location information. 1. Nam

147 SNMP System Configuration interface Trap Managers A trap manager is a managem

148 3. Trap Version: select the SNMP trap version type – v 1 or v2.

149  User ID: set up the user name.  Authentication Password: set up the authenti

150 SNMP V3 configuration interface Group Table Configure SNMP v3 g

151  Security Name (User ID): assign the user name that you have set up in user tab

8 Rear Panel The 3-pronged power plug are located at the Rear Panel o

152 QoS Configuration You can configure Qos policy and priority se

153 QoS Configuration interface Port Base Priority

154 Configure per port priority level.  Port 1 ~ G1& 2: each po

155 1. SNTP Client: enable or disable SNTP function to get the time from the SNTP se

156 CET - Central European FWT - French Winter MET - Middle European

157 4. SNTP Sever URL: set the SNTP server IP address. 5. Daylight Saving Period St

158 Message Description Query A message sent from the querier

159 IGMP Configuration interface Super ring Super ring provide a faster redundant

160 The system also supports the coupling ring that can connect 2 or

161 Security Configuration In this section, you can configure 802.1x, IP, and port s

9 Network Application Desktop Application The switch is designed to be

162 802.1x System Configuration interface 802.1x Per Port Configur

163 802.1x Per Port Setting interface Misc Configuration 1. Quiet Period: set th

164 7. ClickApply. 802.1x Misc Configuration interface Port Secu

165  Add the Static MAC Address You can add static MAC address in switch MAC table

166 Filtering MAC Address By filtering MAC address, the switch

167 All MAC Address You can view the port that connected device’s MAC address and re

168 Factory Default interface Save Configuration Save all configu

169 Troubleshooting This section is intended to help you solve the most common prob

170  Improper Network Topologies It is important to make sure tha

171 Technical Specifications This section provides the specifications of switc

10 Console Management Connecting to the Console Port Use the supp

172 Operational Temp. 0 ~60 , 5%~95%RH Operational Humidity 10% to 90

11 The settings of communication parameters After finished the parameter settings,

Regulatory Approval - FCC Class A - UL 1950 - CSA C22.2 No. 950 - EN6

12 Console login interface

13 CLI Management The system supports two types of console management – CLI

14 configuration mode privileged EXEC mode, or end. Commands Set L

15 reload Global configuration mode Halt and perform a cold restart Switch (config

16 show accounting Privileged EXEC Show username & password Swi

17 Use the duplex configuration command to specify the duplex mode of operation for F

18 flowcontrol on or no flowcontrol Interface configuration mode Use

19 State [Enable | Disable] Interface configuration mode Use the state interface conf

20 show bandwidth Interface configuration mode Display the bandwidth

21 Check OK! NEW: 2 4 Update finished!! VLAN Commands Set Commands Command Level

Content Introduction...

22 [Group name] or [VLAN ID] mode Switch (vlan)# no vlan v2 2 vlan p

23 [3584~3839] range 14 [3840~4094] range 15 VLAN protocol [Groupname] add [portNumbe

24 Priority: 32768 Mac Address: 004063800030 Root_Path_Cost: 0 Root P

25 data unit (BPDU) message from the root switch within this interval, it recomputes

26 learning states last before the port begins forwarding. Use the no

27 no qos level [priority] Global configuration mode [Priority] 0~7 0~3 LOW 4~7 HI Sw

28 show qos low-priority-delay-bound Privileged EXEC mode Show low pr

29 Mac / Filter Table Commands Set Commands Command Level Description Defaults

30 show mac-address-table [static | filter] Privileged EXEC mode Use

31 Port Mirroring Commands Set Commands Command Level Description Defaults Exampl

Port Mirroring Commands Set...

32 Stacking Commands Set Commands Command Level Description Defaul

33 802.1x Commands Set Commands Command Level Description Defaults Example show 802

34 [quietperiod value] Or no 8021x misc quietperiod configuration mod

35 set to the Authorized or Unauthorized state in accordance with the outcome of an a

36 Main Menu There are five selections as follow.  System Configu

37 Main menu line interface  Control Key description: The control keys provided i

38 choose the item, and press “Enter” key to select the item. Statu

39 8. MAC Address: The unique hardware address assigned by manufacturer. System De

40 name into IP addresses. Because domain name are alphabetic,

41 DHCP Configuration It short for Dynamic Host Configuration Protocol that is a pro

Port Base VLAN Configure...

42 The system provides the DHCP server function. Enable the DHCP serv

43 DHCP Server Configuration interface DHCP Client Entries When the DHCP server f

44 DHCP Client Entries interface Port and IP Bindings You can ass

45 Port and IP Bindings interface Firmware Update It provides user to update firm

46 4. File Name: type the image file name. 5. Press “ESC” to back t

47 System Log Configuration interface System Log Configuration Configuring the sy

48 System Log Configuration interface Event Configuration You can

49 Email Alert Configuration When the specific events occur, the system will send

50 Email Alert Configuration interface SMTP Configuration You can

51 SMTP Configuration interface Recipient’s email Configuration Assign the forw

Security Configuration ...

52 Recipient’s email Configuration interface Security Manager You

53 Security Manager interface

54 Port Configuration In this section, you can view port counter inf

55 Port Counter interface Port Control Configuration You can set up every port st

56 9. To view the State of Ports, select <Refresh> to get the

57 mode, more detail information refers to IEEE 802.3ad. Aggregator setting 1.

58 Trunk Configuration — Aggregator Setting interface Aggregator I

59 Trunk Configuration – Aggregator Information interface State Activity When you

60 c. If you are active LACP’s actor, when you are select

61 3. Source Port (TX/RX): select the monitor mode of each port. You can choose whic

View the Single Port Information ...

62 broadcast/multicast/unknown unicast packet, broadcast/multicast

63 Protocol Configuration In this section, you can configure VLAN, RST, SNMP, SNTP,

64 VLAN Mode Selection interface Port Base VLAN Configure Add VLA

65 Group Add 1. Group Name: Type a name for the new VLAN, ex: VLAN01. 2. VID:

66 Group Add interface Group Remove You can remove unwanted VLAN

67 Group Remove interface Group List Display the all VLAN groups’ information.

68 Group List interface 802.1Q VLAN Configure You configure GVRP

69 802.1Q VLAN Configuration interface GVRP Setting GVRP (Generic Attribute Re

70 GVRP Setting interface Configure VLAN by Port 1. Select the p

71 Configure VLAN by Port interface VLAN List Enable or disable the VLAN group. 1.

Super ring ...

72 Edit VLAN Group interface Rapid Spanning Tree The Rapid Spanni

73 Rapid Spanning Tree interface RSTP System Configuration 1. You can view spann

74  Hello Time (1-10): the time that controls switch sends out the

75 You can configure path cost and priority of every port. 1. Select the port in Por

76 RSTP Per Port Configuration interface SNMP Configuration Simpl

77 SNMP Configuration interface System Options Enter the system name, contact, an

78 SNMP System Options interface Community Strings You can change

79 3. Save the configuration. Add Community Strings interface Trap Managers A tr

80 5. To disable the trap manager, please delete the trap manager IP

81 SNMP V3 configuration interface Context Table Configure SNMP v3 context table

1 Introduction The product is a multi-port switch that can be used to build h

82 SNMP v3_Context Table interface User Table Configure SNMP v3 u

83 SNMP v3_User Table interface Group Table Configure SNMP v3 group table. 1. Us

84 SNMP v3_Group Table interface Access Table Configure SNMP v3 ac

85 SNMP v3_AccessTable interface  Add Table Add the access table. 1. Context:

86  Remove/Browse Table Remove and Browse access table.

87 MIBview Table Configure MIB view table.

88 SNMP v3_MIBviewTable interface  Add Table Add MIB view table

89  Remove/Browse Table Remove and Browse MIBview table.

90 QoS Configuration You can configure Qos policy and priority s

91 QoS Configuration interface QoS Policy and Priority Type  Select the Oos Poli